GPScorrect™ extension for ESRI ArcGIS software
DOWNLOADS
Version 3.10
Version 3.02
Version 3.01
Version 3.00
Version 2.42
Version 2.41
Version 2.40
Version 2.30
Other Downloads
Support Notes
_______________________________
Version 3.10
GPScorrect version 3.10 requires ArcPad version 7.00 or later. GPScorrect version 3.10 does not support earlier versions of ArcPad. ArcPad must be installed onto your PC or Windows Mobile device before you install the v3.10 GPScorrect extension.
A GPScorrect extension installation code can only be activated on one Windows Mobile (version 5.0 or 6) powered device at a time. If you activate an installation code on the wrong device or need to change the device the extension is activated on you will need to contact your Trimble Reseller to request it be deactivated.
Support for the Trimble GPS Pathfinder ProXRT receiver running firmware version 3.60 has been discontinued. You will need to update your receiver's firmware to version 3.72. For the firmware version 3.72 and instructions on how to upgrade your existing receiver firmware, go to http://www.trimble.com/pathfinderproxrt_ts.asp
New Features
Entitlement
-
If you have a Software Maintenance Extension valid on or after 1 Dec 2009, you are entitled to v3.10. Use your existing installation code to install v3.10.
-
If you do not have a Software Maintenance Extension valid on 1 Dec 2009, contact your local Tri-Global Representative for details on upgrading to v3.10.
To post process data collected with the GPScorrect v3.10 extension, one of the following is required:
Version 3.02
GPScorrect version 3.02 requires ArcPad version 7.00 or later. GPScorrect version 3.02 does not support earlier versions of ArcPad. ArcPad must be installed onto your PC or Windows Mobile device before you install the v3.02 GPScorrect extension.
A GPScorrect extension installation code can only be activated on one Windows Mobile (version 5.0 or 6) powered device at a time. If you activate an installation code on the wrong device or need to change the device the extension is activated on you will need to contact your Trimble Reseller to request it be deactivated.
New Features
- An issue that did not allow real-time solutions to converge to 10 cm when using a GeoXH handheld running firmware version 2.11 has been fixed.
- Version 3.02 of the GPScorrect extension includes the following changes:
- Support for the Trimble Yuma tablet rugged tablet computer.
- Support for the Trimble GPS Pathfinder ProXRT receiver running firmware version 3.72.
- Support for the Indian GAGAN satellites. The frequencies used by the Indian GAGAN SBAS system have been added to the SBAS.ini file; you can now manually select these frequencies for use with receivers that support them.
- Support for OmniSTAR frequencies that have 500 Hz offsets (4th decimal place).
- Support for software activation on field computers powered by the Windows Mobile version 5.0 software or version 6 operating system. For more information, refer to the Trimble GPScorrect Extension Getting Started Guide.
- The heading display for SiRF-based receivers now correctly displays headings between 326 and 359 degrees.
- A bug that allowed the wrong date to be written to the SSF correction file has been corrected.
- A bug that allowed the SSF to become corrupt due to a missing ArcPad vertex has been corrected.
- A bug caused by excessive receiver clock drift that prevented data from being post-processed has been corrected.
- Read the version 3.02 Release Notes for details on how to perform the installation.
- Version 3.00 or later of the GPScorrect extension no longer ships with an Updater Utility.
- Support for the Trimble GPS Pathfinder ProXRT receiver running firmware version 3.60 has been discontinued. You will need to update your receiver's firmware to version 3.72. For the firmware version 3.72 and instructions on how to upgrade your existing receiver firmware, go to GPSPathfinder_ProXRT.html.
Entitlement
- If you have a Software Maintenance Extension valid on or after 2 Dec 2008, you are entitled to v3.02. Use your existing installation code to install v3.02.
- If you do not have a Software Maintenance Extension valid on 2 Dec 2008, contact your local Tri-Global Representative for details on upgrading to v3.02.
To post process data collected with the GPScorrect v3.02 extension, one of the following is required:
- Version 4.10 of the GPS Pathfinder Office software with the latest software updates.
- Version 2.10 of the GPS Analyst extension for ESRI ArcGIS software with the latest software updates.
TerraSync/GPScorrect Activation Utility Patch
(Activator.zip - 79 KB)
If you are activating the TerraSync or GPScorrect software from a computer with a 64 bit operating system you will need to replace the Activator.exe file with this file. Instructions for doing this are included in this Support Note.
Version 3.01
GPScorrect version 3.01 requires ArcPad version 7.00 or later. GPScorrect version 3.01 does not support earlier versions of ArcPad. ArcPad must be installed onto your PC or Windows Mobile device before you install the v3.01 GPScorrect extension.
A GPScorrect extension installation code can only be activated on one Windows Mobile (version 5.0 or 6) powered device at a time. If you activate an installation code on the wrong device or need to change the device the extension is activated on you will need to contact your Trimble Reseller to request it be deactivated.
New Features
- Support for the Trimble Yuma tablet rugged tablet computer.
- Support for the Trimble GPS Pathfinder ProXRT receiver running firmware version 3.72.
- Support for the Indian GAGAN satellites. The frequencies used by the Indian GAGAN SBAS system have been added to the SBAS.ini file; you can now manually select these frequencies for use with receivers that support them.
- Support for OmniSTAR frequencies that have 500 Hz offsets (4th decimal place).
- Support for software activation on field computers powered by the Windows Mobile version 5.0 software or version 6 operating system. For more information, refer to the Trimble GPScorrect Extension Getting Started Guide.
- The heading display for SiRF-based receivers now correctly displays headings between 326 and 359 degrees.
- A bug that allowed the wrong date to be written to the SSF correction file has been corrected.
- A bug that allowed the SSF to become corrupt due to a missing ArcPad vertex has been corrected.
- A bug caused by excessive receiver clock drift that prevented data from being post-processed has been corrected.
- Read the version 3.01 Release Notes for details on how to perform the installation.
Version 3.01 of the GPScorrect extension includes the following changes:
- Version 3.00 or later of the GPScorrect extension no longer ships with an Updater Utility.
- Support for the Trimble GPS Pathfinder ProXRT receiver running firmware version 3.60 has been discontinued. You will need to update your receiver's firmware to version 3.72. For the firmware version 3.72 and instructions on how to upgrade your existing receiver firmware, go to http://www.trimble.com/pathfinderproxrt_ts.asp.
Entitlement
- If you have a Software Maintenance Extension valid on or after 2 Dec 2008, you are entitled to v3.01. Use your existing installation code to install v3.01.
- If you do not have a Software Maintenance Extension valid on 2 Dec 2008, contact your local Trimble representative for details on upgrading to v3.01.
To post process data collected with the GPScorrect v3.01 extension, one of the following is required:
- Version 4.10 of the GPS Pathfinder Office software with the latest software updates.
- Version 2.10 of the GPS Analyst extension for ESRI ArcGIS software with the latest software updates.
v3.01 - GPScorrect, Software for Windows Mobile 5.0 / 6
(GPScorrectWMWebRelease.exe - 8661 KB)
v3.01 - GPScorrect, Software for Pocket PC 2003
(GPScorrectPPC2003WebRelease.exe - 7496 KB)
v3.01 - GPScorrect, Software for Windows 2000 and XP (Home, Professional, or Tablet PC Edition)
(GPScorrectDesktopSetup.exe - 15277 KB)
v3.0x - GPScorrect software Language Files
Language files are available in English, Spanish, German, French, Chinese, and Japanese.
_______________________________
Version 3.00
GPScorrect version 3.00 requires ArcPad version 7.00 or later. GPScorrect version 3.00 does not support earlier versions of ArcPad. ArcPad must be installed onto your PC or Windows Mobile device before you install the v3.00 GPScorrect extension.
New Features
Entitlement
-
If you have a Software Maintenance Extension valid on or after 2 Dec 2008, you are entitled to v3.00. Use your existing installation code to install v3.00.
-
If you do not have a Software Maintenance Extension valid on 2 Dec 2008, contact your local Tri-Global representative for details on upgrading to v3.00.
To post process data collected with the GPScorrect v3.00 extension, one of the following is required:
v3.00 - GPScorrect, Software for Windows Mobile 5.0 / 6
(GPScorrectWMWebRelease.exe - 8732 KB) v3.00 - GPScorrect, Software for Pocket PC 2003
(GPScorrectPPC2003WebRelease.exe - 7568 KB) v3.00 - GPScorrect, Software for Windows 2000 and XP (Home, Professional, or Tablet PC Edition)
(GPScorrectDesktopSetup.exe - 15265 KB)
_________________________________
Version 2.42
GPScorrect version 2.42 requires ArcPad version 7.00 or later. GPScorrect version 2.42 does not support earlier versions of ArcPad. ArcPad must be installed onto your PC or Windows Mobile device before you install the v2.42 GPScorrect extension.
New Features
Entitlement
-
If you have a Software Maintenance Extension valid on or after 2 Dec 2008, you are entitled to v2.42. Use your existing installation code to install v2.42.
-
If you do not have a Software Maintenance Extension valid on 2 Dec 2008, contact your local Tri-Global representative for details on upgrading to v2.42.
To post process data collected with the GPScorrect v2.42 extension, one of the following is required:
v2.42 - GPScorrect, Software for Windows Mobile 5.0 / 6
(GPScorrectWMWebRelease.exe - 8497 KB)
v2.42 - GPScorrect, Software for Pocket PC 2003
(GPScorrectPPC2003WebRelease.exe - 7598 KB)
v2.42 - GPScorrect, Software for Windows 2000 and XP (Home, Professional, or Tablet PC Edition)
(GPScorrectDesktopSetup.exe - 16020 KB)
_______________________________
Version 2.41
GPScorrect version 2.41 requires ArcPad version 7.00 or later. GPScorrect version 2.41 does not support earlier versions of ArcPad. ArcPad must be installed onto your PC or Windows Mobile device before you install the v2.41 GPScorrect extension.
New Features
-
Support for the GeoExplorer 2008 series handhelds. These handhelds have an integrated GPS receiver.
-
Read the version 2.41 Release Notes for details on how to perform the installation, and the new features in version 2.41.
Entitlement
-
If you purchased a copy of GPScorrect from 15 February 2008 you are entitled to version 2.41.
-
If you have a Software Maintenance Extension valid on or after 15 May 2008, you are entitled to v2.41. Use the installation code to install v2.41.
-
If you do not have a Software Maintenance Extension valid on 15 May 2008, contact your local Trimble representative for details on upgrading to v2.41.
To post process data collected with the GPScorrect v2.41 extension, one of the following is required:
v2.41 - GPScorrect, Software for Windows Mobile 5.0 / 6
(GPScorrectWMWebRelease.exe - 8479 KB) v2.41 - GPScorrect, Software for Pocket PC 2003
(GPScorrectPPC2003WebRelease.exe - 7585 KB) v2.41 - GPScorrect, Software for Windows 2000 and XP (Home, Professional, or Tablet PC Edition)
(GPScorrectDesktopSetup.exe - 16004 KB) v2.4x - GPScorrect Updater Utility
(Updater Setup.exe - 14052 KB)
It is recommended that you download and install the GPScorrect Updater Utility. This utility allows you to update your v2.4x software with any new updates.
The Updater Utility should be run periodically when you are connected to your device running GPScorrect and when your PC is connected to the internet. The utility will inform you when new updates are available and assist you to update your GPScorrect software.
_______________________________
Version 2.40
GPScorrect version 2.40 requires ArcPad version 7.00 or later. GPScorrect version 2.40 does not support earlier versions of ArcPad. ArcPad must be installed onto your PC or CE device before you install the v2.40 GPScorrect extension.
New Features
-
Support for the GPS Pathfinder ProXRT receiver
-
Support for GLONASS satellites tracked and used by the GPS Pathfinder ProXRT receiver to compute positions
-
Changes to the display of estimated accuracy values on the status bar
-
Read the version 2.40 Release Notes for details on how to perform the installation, and the new features in version 2.40.
Entitlement
-
If you purchased a copy of GPScorrect from 4 December 2007 you are entitled to version 2.40.
-
If you have a Software Maintenance Extension valid on or after 3 March 2008, you are entitled to v2.40. Use the installation code to install v2.40.
-
If you do not have a Software Maintenance Extension valid on 3 March 2008, contact your local Trimble representative for details on upgrading to v2.40.
To post process data collected with the GPScorrect v2.40 extension, one of the following is required:
v2.40 - GPScorrect, Software for Windows 2000 and XP (Home, Professional, or Tablet PC Edition)
(GPScorrectDesktopSetup.exe - 15541 KB) v2.40 - GPScorrect, Software for Windows Mobile 5.0 / 6
(GPScorrectWMWebRelease.exe - 8370 KB) v2.40 - GPScorrect, Software for Pocket PC 2003
(GPScorrectPPC2003WebRelease.exe - 7478 KB) v2.4x - GPScorrect Updater Utility
(Updater Setup.exe - 14052 KB)
It is recommended that you download and install the GPScorrect Updater Utility. This utility allows you to update your v2.4x software with any new updates.
The Updater Utility should be run periodically when you are connected to your device running GPScorrect and when your PC is connected to the internet. The utility will inform you when new updates are available and assist you to update your GPScorrect software.
_______________________________
Version 2.30
GPScorrect version 2.30 requires ArcPad version 7.00 or later. GPScorrect version 2.30 does not support earlier versions of ArcPad. ArcPad must be installed onto your PC or CE device before you install the v2.30 GPScorrect extension.
v2.30 - GPScorrect, Software for Windows 2000 and XP (Home, Professional, or Tablet PC Edition)
(GPScorrectDesktopSetup.exe - 15361 KB) v2.30 - GPScorrect, Software for Windows Mobile 5.0 / 6
(GPScorrectWMWebRelease.exe - 7122 KB) v2.30 - GPScorrect, Software for Pocket PC 2003
(GPScorrectPPC2003WebRelease.exe - 7094 KB) v2.30 - GPScorrect, Software for Windows CE .NET (4.2 and later)
(GPScorrectGeoExplorerWinCE.NETWebRelease.exe - 6592 KB) GPScorrect Updater Utility
(Updater Setup.exe - 3163 KB)
It is recommended that you download and install the GPScorrect Updater Utility. This utility allows you to update your v2.3x software with any new updates.
The Updater Utility should be run periodically when you are connected to your device running GPScorrect and when your PC is connected to the internet. The utility will inform you when new updates are available and assist you to update your GPScorrect software.
_______________________________
_______________________________
Other Downloads SBAS.INI
(SBAS.ini - KB)
Updated: 1 August 2007
-
Contains the list of SBAS satellites, including the two recently launched WAAS satellites - PRNs 135 and 138.
-
Required when using Custom mode in Trimble field software to select particular satellites to track, and exclude from the tracking list.
-
Details on the new WAAS satellites and how to install the SBAS.INI file are included in the Support Note titled Status Update: New WAAS Satellites and Trimble GPS Receivers.
SATDGPS.INI
File
(Satdgps.ini - 2 KB)
Updated: 21 April 2009
- Contains the list of frequencies used by satellite DGPS providers.
- Updated for changes to the satellite frequency for use in New Zealand.
- If you have TerraSync, GPS Controller, GPScorrect, or an application developed using the GPS Pathfinder Tools SDK installed on a PC, copy this file into the folder C:\Program Files\Common Files\Trimble\Config.
- If you have TerraSync, GPS Controller, GPScorrect, or an application developed using the GPS Pathfinder Tools SDK installed on a Windows CE or Windows Mobile for Pocket PCs operating system, copy this file into the folder \Program Files\Common Files\Trimble\Config. This folder will be located on the Disk or in RAM depending on where the software is installed
- If you have GPS Analyst v2.00 or later, copy this file into the folder C:\Program Files\Trimble\GPS Analyst\Bin.
- If you have GPS Analyst v1.20 or earlier, copy this file into the folder C:\Program Files\Common Files\Trimble\Config.
- If you are using Asset Surveyor download this version of SATDGPS.INI and use the GPS Pathfinder Office Data Transfer utility to load this file onto your device.
ANTENNA.INI File (Translated)
(TranslatedAntenna.zip - 349 KB)
Translated Antenna files for Mapping & GIS Software (updated 10 March 2008).
This zip file contains translated antenna files for use with the following software: Antenna types, names, and measurement points have been translated in the following languages:
-
Chinese (Simplified)
-
Chinese (Traditional)
-
Croatian
-
Czech
-
Danish
-
Dutch
-
English
-
Estonian
-
Finnish
-
French
-
German
-
Greek
-
Hungarian
-
Italian
-
Japanese
-
Korean
-
Norwegian
-
Polish
-
Portuguese
-
Russian
-
Serbian
-
Spanish
-
Swedish
-
Turkish
To use a translated antenna file see instructions in the readme.txt file.
_______________________________
Support Notes
Mapping and GIS Product Compatibility List
(MGIS_SprtNote_Product_Compatibility.pdf - 492 KB)
This document outlines the compatibility between Trimble field devices, versions of Trimble field software, versions of the GPS Pathfinder Office software and Microsoft Windows operating systems.
Submitting Crash Data to Trimble
(MGIS_SprtNote_SubmittingCrashData.pdf - 188 KB)
The Trimble Mapping & GIS Division continues to improve the quality of its products. This support bulletin describes how customers and resellers can send reports to Trimble about critical runtime issues that may occur with Trimble products.
Envío de informes a Trimble sobre problemas de ejecución
(Span MGIS_SprtNote_SubmittingCrashData.pdf - 189 KB)
La División Trimble Mapping & GIS continua mejorando la calidad de sus productos. Este boletín de soporte describe el procedimiento que deben seguir los clientes y distribuidores de Trimble para enviar informes sobre problemas de ejecución críticos que puedan ocurrir con los productos de Trimble.
Trimble GPScorrect Extension for ESRI ArcPad Software: Setting the Antenna Height in the ESRI ArcPad Software
(MGIS_SprtNote_GPScorrect_Antenna_Height.pdf - 254 KB)
The Trimble GPScorrect extension for the ESRI ArcPad software logs GPS position data to a Trimble SSF file. Many of the ESRI ArcPad software settings are used by the GPScorrect extension to ensure the correct positions are logged. This support note recommends that you always set the antenna height in meters in the ESRI ArcPad software so that the GPScorrect extension can correctly read this value.
Installing GPScorrect on a GeoXT or GeoXM running the CE .NET Operating System
(SprtNote_GPScorrect_CENET.pdf - 90 KB)
The GeoXT™/GeoXM™ revision 2.00 operating revision is based on the Microsoft® Windows® CE .NET 4.2 operating system. When you install GPScorrect™ for ESRI® ArcPad® 6.0 onto a GeoXT or GeoXM handheld device that is running the CE .NET operating system, you must use version 1.01 or later of the GPScorrect software. If you try to install GPScorrect version 1.00, you will receive the following error message and you will be unable to install GPScorrect: Win CE does not support the current version of the Software.
This document explains how to resolve this issue.
Trimble GPS Receivers: Status Update for WAAS Satellites
(MGIS_SprtNote_WAAS_Update_May2008.pdf - 294 KB)
This document provides an update on the status of the WAAS (Wide Area Augmentation System) satellites, including the FAA’s expected timeline for the second new WAAS satellite (PRN 138) to be set as operational, and for the older WAAS satellites (PRNs 122 and 134) to be decommissioned. This document describes the Trimble GPS receivers that are able to use the new WAAS satellites, and describes how to install a new SBAS.ini file and configure your GPS receiver to use the new WAAS satellites.
Receptores Trimble GPS: Actualización del estado de los satélites WAAS
(MGIS_SprtNote_WAAS_Update_May2008.pdf - 294 KB)
En este documento se proporciona una actualización sobre el estado de los satélites del Sistema de ampliación de área ancha WAAS (siglas inglesas de Wide Area Augmentation System), información sobre los receptores Trimble® GPS que pueden utilizar los nuevos satélites WAAS (PRN 135 y 138) así como se describe la instalación del nuevo archivo SBAS.ini y la configuración de su receptor GPS para que pueda utilizar los nuevos satélites WAAS.
GPS Pathfinder Pro XRS Receiver: Incorrect Firmware Version
(MGIS_SprtNote_ProXRS_Firmware_Issue.pdf - 183 KB)
An incorrect firmware version was installed on a number of Trimble GPS Pathfinder Pro XRS receivers that were shipped after November 2005. Units with this firmware version cannot use the integrated satellite based augmentation system (SBAS) signals (WAAS / EGNOS) for real-time corrections. This Support Note explains the issue and how to resolve it.
OmniSTAR (Australia and New Zealand): Change in Satellite and Frequency
(MGIS_SprtNote_Omnistar_Optus.pdf - 149 KB)
OmniSTAR is changing the satellite and the frequency on which it broadcasts corrections for Australia and New Zealand. If you use an OmniSTAR-capable receiver in Australia or New Zealand, you must update the data collection software to track the new satellite and frequency. This Support Note describes how to do this.
OmniSTAR AMSC (Western, Central, and Eastern USA) Satellite: New Frequencies
(MGIS_SprtNote_Omnistar_AMSC.pdf - 170 KB)
OmniSTAR is changing the frequency for the North American satellite, AMSC (Western, Central, and Eastern USA), on which it broadcasts corrections. If you use an OmniSTAR-capable receiver in North America, you must update the data collection software to track the new frequencies. This Support Note provides details on how to do this.
GeoExplorer Series Handhelds: Connecting the Receiver to Trimble Mapping & GIS Field Software Through the Serial Clip
(MGIS_SprtNote_GeoExplorer_SerialBaudRate.pdf - 134 KB)
If you use a serial clip to connect the GPS receiver in a Trimble GeoExplorer series handheld to a datalogger, such as a laptop or a PDA, that is running any the following software; TerraSync v2.50, GPS Analyst extension for ESRI ArcGIS v1.10, GPS Pathfinder Tools v2.00, or GPScorrect extension for ESRI ArcPad v1.10, you must change the GPS Connector settings from TSIP Standard to custom settings of 38400, 8, 1, Odd. This Support Notes explains the changes required.
Trimble Planning Software: Setup and Configuration
(MGIS_SprtNote_TrimblePlanning_Setup.pdf - 517 KB)
The Trimble® GPS Pathfinder® Office software version 4 no longer contains the QuickPlan™ software. There is a form of planning available in the TerraSync™ software, for use in the field, but Trimble recognises the continued need for you to plot satellite availability and DOPs, and to key-in obstructions. This Support Note explains how to correctly configure Trimble Planning software for use with MGIS field computers.
OmniSTAR AF-SAT (Central + South Africa) Satellite: New Frequency and Data Rate
(SprtNote_MGIS_Omnistar_AFSAT.pdf - 164 KB)
OmniSTAR is changing the frequency and baud rate for the African satellite, AF-SAT (Central + South Africa), on which it broadcasts corrections. If you use an OmniSTAR-capable receiver in Africa, south of the Sahara, you must update the data collection software to track the new frequency.
Software de planificación de Trimble: Instalación y configuración
(Span MGIS_SprtNote_TrimblePlanning_Setup.pdf - 260 KB)
El software Trimble® GPS Pathfinder® Office versión 4 ya no contiene el software QuickPlan™. En el software TerraSync™ hay un formulario que puede utilizarse para la planificación en el campo, pero Trimble reconoce la necesidad continua que tiene el usuario de trazar la disponibilidad de satélites y los valores DOP y de introducir obstáculos. En esta nota de soporte se explica cómo configurar correctamente el software de planificación para ser utilizado con las computadoras de campo MGIS.
Resolving Communication Errors between the GPS Receiver and Field Software
(SprtNote_ProXR-XRS_Communications.pdf - 28 KB)
To ensure your GPS Pathfinder® Pro XR or Pro XRS receiver communicates correctly with your data collection or data maintenance software, you must use a version of the field software that is compatible with the GPS receiver's embedded software version. This Support Note outlines compatibilities between field software versions and the different embedded software versions of the Pro XR and Pro XRS receivers.
|
